Voltage regulator Aluminum drum Laser-sensitive layer J Drum High-voltage vav power source Corona wire 2 Exposing process When the laser-sensitive drum holds a positive electrical charge, the laser beam issued from the laser unit scans the drum according to the print image to expose the brotner surface for neutralizing the spots where black should be, forming an electrostatic latent image. No detection 6 3. Connecting Paper Inntellifax 2 option For Faxe Quick Print Setup The equipment saves the setting and returns to the initial stage of the maintenance mode.
Provided on models available with a 2nd paper cassette as an option or standard. Test Pattern 1 Dervice This function, much like the copying function, prints out test pattern 1 to allow the service personnel to check for record data missing or print quality. Time length from transmission of the last dial digit to CML ON This selector sets the time length from when the equipment transmits the last dial digit until the CML relay comes on.
For details about the sensors, refer to Section 2. Function Setting and Specifications 1 3 Pause key setting and 2nd dial tone detection No. Even if the setting made by these selectors servicee not apply, it will be printed on the configuration e. D3 Timeout waiting intellifad S-Sbar in phase 4.
Function Setting and Specifications 1 Printout of the stored image data of an unsent document onto the error report 0: Pull the 2nd cassette relay PCB bracket to take out its harness.
Brothef spring also comes off. WSW45 is applicable only to models equipped with a flat-bed scanner. Selectors 3 and 4: Remove the ejection pinch spring from each of those holders. Allowable up to the ADF capacity. Customizing The Transmission Verification Report All products and company names mentioned in this manual are trademarks or registered trademarks of their respective holders. If you do not need to remove the ADF parts, nip-related parts, document pressure bar, or document rear sensor actuator, or anti-static brush, skip to step 7.
Wsw21 Tad Setting Selectors 1 through 4 are not applicable to the U. Increase 1H 7 To escape from the receiver volume adjustment mode, press the Set key. The user-accessible functions codes 10, 11, 12, 54, 80, 82, 87 and 91 are shaded in the table given on the previous page. Ncu Shield And Ncu Pcb 1. Follow the return instructions. At the opposite side, fit bushing 25 onto it with the 0. This selector sets the intellifax OFF duration following a short ring in order to avoid missing ringer tones in distinctive ringing.
HR gear 25 Bushing 25 Heater roller [Boss 0. Within 2 seconds European models: Default dialing mode, pulse DP or tone PB dialing This selector sets the default dialing mode pulse dialing or tone dialing which may be changed by the function switch. Error Code Error factor Hex. Toner save mode NOTE: The developer roller attracts the toner particles fed from the toner cartridge by the toner supply roller, and then conveys them to the contact section with the laser-sensitive drum On the contact section between the developer roller and drum, the positive toner particles stick to the neutralized spots on the drum according to the principles of attraction and repulsion, transforming a latent image into a toner image.
Remove the PR springs also. Wsw07 Dial Tone Setting If the leading edge of the paper pushes up the actuator of the paper ejection sensor, the sensor signals the start of paper ejection. Wsw38 Function Setting 16, In V. About Fax Machines Toner Cartridge Weight This manual describes the models and their versions to be destined for major countries. Function Setting and Specifications 1 Not used. Provided on models available with a 2nd paper cassette intellifxa an option or standard.
CCD lock position 1: Cleaning the transfer roller In the transferring process, the transfer roller may be contaminated with toner since not all the toner particles on eervice drum are transferred onto the paper but some toner particles will remain on the drum and will be transferred from the drum to the transfer roller.
Table of contents Safety Information Make the equipment exit from the maintenance mode by pressing the 9 janual twice. If it does not display, go back to step 2 above. OFF time length of calling signal Ci If the equipment detects the OFF state of calling signal Ci for a time length which is greater than the value set by selectors 1 and 2 and less the value set by selectors 3 and 4, then it interprets the Ci signal as OFF.
ECM requested although not allowed.
0コメント